Add BLE_LOG_GET_FRAME_SN() on the buffer-full loss path so the SN
counter advances even when frames are dropped. This allows the console
to detect firmware-side buffer loss via SN gaps. Bump BLE_LOG_VERSION
to reflect the semantic change.
(cherry picked from commit 42f2aeedb7)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
Introduce stream write API with deferred frame encapsulation for UART
redirection on port 0. Redirected data is now properly framed (header +
payload + checksum) instead of being sent as raw ASCII, preventing frame
parser sync oscillation on the receiver.
- Add stream_seal/stream_write/stream_flush in ble_log_lbm.c
- Add BLE_LOG_SRC_REDIR source and BLE_LOG_UART_REDIR_ENABLED gate
- Simplify redir_uart_tx_chars and timer callback to use stream API
- Flush pending stream data in ble_log_prph_deinit
- Make get_trans static (no external callers after refactor)
- Move UART wrap linker flags outside CONFIG_BT_ENABLED guard
- Default UART DMA peripheral when SOC_UHCI_SUPPORTED
- Default baud rate 921600 -> 3000000
(cherry picked from commit a181fc156d)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
Replace embedded ble_log_enh_stat_t (packed wire struct) inside
ble_log_stat_mgr_t with flat uint32_t counters. Natural 4-byte
alignment ensures each load/store compiles to a single l32i/s32i
on Xtensa/RISC-V, making individual field access atomic without
locks.
Build the packed wire format on the stack inside a critical section
in ble_log_write_enh_stat() so the full snapshot is consistent.
(cherry picked from commit 4d193873f1)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
Remove CONFIG_BLE_LOG_PAYLOAD_CHECKSUM_ENABLED conditional compilation
-- payload checksum is always computed over the full frame.
Remove CONFIG_BLE_LOG_XOR_CHECKSUM_ENABLED conditional -- XOR checksum
is always used; delete the sum checksum dead code path.
Remove CONFIG_BLE_LOG_ENH_STAT_ENABLED conditional -- enhanced
statistics (frame/byte counters per source) are always active.
Remove incorrect select on choice symbol
BT_LE_CONTROLLER_LOG_MODE_BLE_LOG_V2 from BLE_LOG_IS_ESP_CONTROLLER.
(cherry picked from commit 3eb2f57605)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
Move ble_log_spi_out.c and ble_log_spi_out.h into a deprecated/
subdirectory under components/bt/common/ble_log/. Extract all
BT_BLE_LOG_SPI_OUT_* Kconfig options into deprecated/Kconfig.in
with an if-block to reduce depends-on repetition, sourced from
ble_log/Kconfig.in inside a "Legacy SPI Log Output (Deprecated)"
menu. Add mutual exclusion with BLE_LOG_ENABLED so that the legacy
SPI Out and the new BLE Log Module cannot be enabled simultaneously.
Update CMakeLists.txt source path and add deprecated/include to
include dirs so existing callers are unaffected. The BLE Log
Module's SPI Master DMA peripheral transport is the replacement.
(cherry picked from commit e2d38955de)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
Delete ble_log_uhci_out.c and its header. Remove the UHCI Out source
from CMakeLists.txt and all BT_BLE_LOG_UHCI_OUT_* Kconfig options.
Remove per-chip BT_LE_CONTROLLER_LOG_UHCI_OUT_ENABLED Kconfig and
all UHCI Out caller references in esp32c5/c6/h2 controller bt.c.
Update ble_log_console README to reference the new BLE Log Module
UART DMA config. The functionality is superseded by the BLE Log
Module's UART DMA peripheral transport.
(cherry picked from commit d51892380b)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
The Key Manager holds a key usage register, thus, the Key Manager peripheral
clock must be enabled even for efuses-based key operations to route the
crypto operations to correctly to the efuses (default is Key Manager)
Zhou Xiao
Mahavir Jain
Jiang Jiang Jian
yinqingzhao
wuzhenghui
Laukik Hase
harshal.patil
Marius Vikhammer
Ashish Sharma
Konstantin Kondrashov
morris
Martin Vychodil
linruihao
Sajia
Rahul Tank
Martin Vychodil
radek.tandler
C.S.M
xiongweichao
Chen Jichang