mirror of
https://github.com/espressif/esp-idf.git
synced 2026-10-01 18:50:34 +03:00
50 lines
1.6 KiB
Plaintext
50 lines
1.6 KiB
Plaintext
# This file was generated using idf.py save-defconfig. It can be edited manually.
|
|
# Espressif IoT Development Framework (ESP-IDF) Project Minimal Configuration
|
|
#
|
|
|
|
CONFIG_BT_ENABLED=y
|
|
CONFIG_BT_NIMBLE_ENABLED=n
|
|
CONFIG_BT_BLUEDROID_ENABLED=y
|
|
CONFIG_BT_CLASSIC_ENABLED=n
|
|
CONFIG_BT_CONTROLLER_ENABLED=y
|
|
CONFIG_BT_BLE_ENABLED=y
|
|
CONFIG_BT_BLE_50_FEATURES_SUPPORTED=y
|
|
CONFIG_BT_ACL_CONNECTIONS=1
|
|
CONFIG_BT_GATT_MAX_SR_PROFILES=12
|
|
CONFIG_BT_GATTC_NOTIF_REG_MAX=30
|
|
CONFIG_BT_BLE_FEAT_ISO_EN=y
|
|
|
|
CONFIG_BT_ISO_MAX_CHAN=2
|
|
|
|
CONFIG_BT_TMAP=y
|
|
CONFIG_BT_CAP_ACCEPTOR=y
|
|
CONFIG_BT_BAP_SCAN_DELEGATOR=y
|
|
CONFIG_BT_BAP_BROADCAST_SINK=y
|
|
CONFIG_BT_VCP_VOL_REND=y
|
|
CONFIG_BT_AUDIO_CODEC_CFG_MAX_METADATA_SIZE=60
|
|
|
|
CONFIG_PARTITION_TABLE_SINGLE_APP_LARGE=y
|
|
|
|
CONFIG_FREERTOS_HZ=1000
|
|
|
|
# To place LE Audio .bss + control-plane heap in PSRAM, uncomment the
|
|
# lines below (needs a PSRAM-capable target, e.g. esp32s31/esp32h4).
|
|
# CONFIG_SPIRAM=y
|
|
# CONFIG_SPIRAM_ALLOW_BSS_SEG_EXTERNAL_MEMORY=y
|
|
# CONFIG_BT_ISO_BSS_SEG_EXTERNAL_MEMORY=y
|
|
# CONFIG_BT_ISO_HEAP_EXTERNAL_MEMORY=y
|
|
# CONFIG_BT_AUDIO_BSS_SEG_EXTERNAL_MEMORY=y
|
|
# CONFIG_BT_AUDIO_HEAP_EXTERNAL_MEMORY=y
|
|
|
|
# Bandwidth-optimized (critical-only) compressed BLE Audio/ISO logging over
|
|
# UART DMA. Pins shown are for esp32s31 (UART0 TX = GPIO58, 3000000 baud); set
|
|
# CONFIG_BLE_LOG_PRPH_UART_DMA_* values to the port/pin your capture reads.
|
|
# CONFIG_BLE_LOG_ENABLED=y
|
|
# CONFIG_BT_LOG_CRITICAL_ONLY=y
|
|
# CONFIG_BLE_COMPRESSED_LOG_ENABLE=y
|
|
# CONFIG_BLE_ISO_COMPRESSED_LOG_ENABLE=y
|
|
# CONFIG_BLE_LOG_PRPH_UART_DMA=y
|
|
# CONFIG_BLE_LOG_PRPH_UART_DMA_PORT=0
|
|
# CONFIG_BLE_LOG_PRPH_UART_DMA_BAUD_RATE=3000000
|
|
# CONFIG_BLE_LOG_PRPH_UART_DMA_TX_IO_NUM=58
|