Add BLE_LOG_GET_FRAME_SN() on the buffer-full loss path so the SN
counter advances even when frames are dropped. This allows the console
to detect firmware-side buffer loss via SN gaps. Bump BLE_LOG_VERSION
to reflect the semantic change.
Introduce stream write API with deferred frame encapsulation for UART
redirection on port 0. Redirected data is now properly framed (header +
payload + checksum) instead of being sent as raw ASCII, preventing frame
parser sync oscillation on the receiver.
- Add stream_seal/stream_write/stream_flush in ble_log_lbm.c
- Add BLE_LOG_SRC_REDIR source and BLE_LOG_UART_REDIR_ENABLED gate
- Simplify redir_uart_tx_chars and timer callback to use stream API
- Flush pending stream data in ble_log_prph_deinit
- Make get_trans static (no external callers after refactor)
- Move UART wrap linker flags outside CONFIG_BT_ENABLED guard
- Default UART DMA peripheral when SOC_UHCI_SUPPORTED
- Default baud rate 921600 -> 3000000
Replace embedded ble_log_enh_stat_t (packed wire struct) inside
ble_log_stat_mgr_t with flat uint32_t counters. Natural 4-byte
alignment ensures each load/store compiles to a single l32i/s32i
on Xtensa/RISC-V, making individual field access atomic without
locks.
Build the packed wire format on the stack inside a critical section
in ble_log_write_enh_stat() so the full snapshot is consistent.
Remove CONFIG_BLE_LOG_PAYLOAD_CHECKSUM_ENABLED conditional compilation
-- payload checksum is always computed over the full frame.
Remove CONFIG_BLE_LOG_XOR_CHECKSUM_ENABLED conditional -- XOR checksum
is always used; delete the sum checksum dead code path.
Remove CONFIG_BLE_LOG_ENH_STAT_ENABLED conditional -- enhanced
statistics (frame/byte counters per source) are always active.
Remove incorrect select on choice symbol
BT_LE_CONTROLLER_LOG_MODE_BLE_LOG_V2 from BLE_LOG_IS_ESP_CONTROLLER.
Move ble_log_spi_out.c and ble_log_spi_out.h into a deprecated/
subdirectory under components/bt/common/ble_log/. Extract all
BT_BLE_LOG_SPI_OUT_* Kconfig options into deprecated/Kconfig.in
with an if-block to reduce depends-on repetition, sourced from
ble_log/Kconfig.in inside a "Legacy SPI Log Output (Deprecated)"
menu. Add mutual exclusion with BLE_LOG_ENABLED so that the legacy
SPI Out and the new BLE Log Module cannot be enabled simultaneously.
Update CMakeLists.txt source path and add deprecated/include to
include dirs so existing callers are unaffected. The BLE Log
Module's SPI Master DMA peripheral transport is the replacement.
Delete ble_log_uhci_out.c and its header. Remove the UHCI Out source
from CMakeLists.txt and all BT_BLE_LOG_UHCI_OUT_* Kconfig options.
Remove per-chip BT_LE_CONTROLLER_LOG_UHCI_OUT_ENABLED Kconfig and
all UHCI Out caller references in esp32c5/c6/h2 controller bt.c.
Update ble_log_console README to reference the new BLE Log Module
UART DMA config. The functionality is superseded by the BLE Log
Module's UART DMA peripheral transport.
Add ble_log_write_hci macro that encodes upstream/downstream direction
in MSB of HCI type byte. Update all 4 callsites (NimBLE + Bluedroid)
to use the new macro. Parser reads MSB to determine direction;
backward compatible (old firmware MSB=0 defaults to "sent").
(cherry picked from commit 8fd5dbb730)
Co-authored-by: Zhou Xiao <zhouxiao@espressif.com>
