This commit adds/updates the USB PHY related HAL APIs. The following changes
are made:
- Updated 'usb_wrap_hal.h' API
- Added 'usb_serial_jtag_hal.h' API
- Added LL cap macros to distinguish feature differences between the LLs of
different targets:
- '..._LL_EXT_PHY_SUPPORTED' indicates whether the USB WRAP/USJ supports
routing to an external FSLS PHY.
- Tidied up some RCC LL functions and their callers.
- Added 'usb_wrap_types.h' and 'usb_serial_jtag_types.h' to provide types used
in LLs.
- Fixed some spelling/naming issues as part of code-spell pre-commit
This commit rewrite the 'usb_wrap_ll.h' API as follows:
- All APIs renamed from 'usb_fsls_phy_ll_...()' to 'usb_wrap_ll_...()'
- APIs now match their equivalent counter parts in 'usb_serial_jtag_ll.h'
For targets that only contain a USJ peripheral (and not a DWC OTG), their
'usb_fsls_phy_ll.h' headers only contain a single function
('usb_fsls_phy_ll_int_jtag_enable()') whose feature is already covered by
functions in 'usb_serial_jtag_ll.h'. Thus, this header is redundant.
This commit does the following:
- Remove 'usb_fsls_phy_ll.h' for targets that only contain a USJ peripheral
- Rename 'usb_fsls_phy_[hal|ll].[h|c]' to `usb_wrap_[hal|ll].[h|c]` for targets
that contain a DWC OTG peripheral. This better reflects the underlying peripheral
that the LL header accesses.
This commit updates the HCD API to allow port resets to occur even if pipes
are allocated. The pipes cannot be active and the port reset will simply
restore the pipes (by reinitializing their channel registers) following the
reset.
Changes:
- Allow port resets while channels are allocated
- Remove pipe persistance API 'hcd_pipe_set_persist_reset()'
Increase LP_UART_EMPTY_THRESH_DEFAULT value to 4. The original value
could cause the FIFO become empty before filling next data into the FIFO
when the buadrate is high. TX_DONE interrupt would raise before actual
transmission complete in such case.
This commit renames USB PHY related HAL files from "usb_phy_xxx" to
"usb_fsls_phy_xxx" since they are only designed to support Full-Speed/Low-Speed
Serial USB PHYs. This renmaing is done to accommodate future USB PHYs that use
other PHY interfaces (e.g., UTMI, ULPI etc).
This commit updates the "*_struct.h" files for the USB OTG peripheral:
- Added/removed some missing/non-existing register fields
- Added "reserved" place holders for registers that are missing due to IP
configuration.
- Added "usb_dwc_cfg.h" listing the USB OTG IP configuration for each target.
- Updated LL/HAL according to register field updates. Also tidied up the include
directives in those headers.
There are a bunch of cases you might want some pins not exposed.
Eg.
* Reading say 8 bit data and outputting the top 5 bits, discarding the rest by not mapping those data pins to output pins
* Not using hsync/vsync because sync data is embedded within the data bits for more timing flexibility (eg. interlacing).
* Using the LCD module as a high speed parallel data output bus, with no need for sync/control pins.
Removing this validation makes these cases work.
Merges https://github.com/espressif/esp-idf/pull/13103
morris
Song Ruo Jing
wuzhenghui
Darian Leung
Marius Vikhammer
Li Shuai
harshal.patil
Cao Sen Miao
Jeroen Domburg
hongshuqing
Tomas Rezucha
gaoxu
Jiang Jiang Jian
zwx
laokaiyao
Lou Tianhao
xiaqilin