fix(bt/example): Add print the device name to verify if it matches in HID example
Closes IDFCI-9124 and IDFCI-3631
See merge request espressif/esp-idf!50375
Remove ~50 duplicate local definitions of ALIGN_UP/ALIGN_DOWN/ALIGN_UP_BY/
ALIGN_DOWN_BY across the codebase and replace them with canonical
ESP_ALIGN_UP/ESP_ALIGN_DOWN from esp_macros.h.
pytest_gcov hardcoded `__idf_<component>.dir/` as the per-component CMake
intermediate directory where each .gcda is expected to land. The directory
name is build-system specific (Build system v1 uses `__idf_<component>.dir`,
Build system v2 uses `_idf_<component>.dir`). Asserting on a single literal
made every test_gcov_uart run fail under Build system v2 even though the
chip was streaming valid coverage data and the host-side UartGcovCapture
was writing the files to the build's actual layout.
Probe `CMakeFiles/*_<component>.dir/` and prefer the candidate whose .gcno
files were emitted by the active build, so the assertion follows the build
output rather than dictating it.
Add Wi-Fi Aware group-key support to secured NDPs so group-addressed
traffic can be protected, for interop with iOS/macOS peers:
- GTK (NCS-GTK-CCM-128) protects group-addressed data.
- IGTK/BIGTK (BIP) protect group management traffic - multicast SDFs,
Beacons.
Capabilities are advertised in the CSIA IE: group_data_prot maps to GTKSA,
group_mgmt_prot to IGTKSA/BIGTKSA. The CSIA cannot encode IGTK/BIGTK
without GTK (WiFi Aware spec 9.5.21.2, Table 122), so enabling group_mgmt_prot
forces group_data_prot on for every secured service.
Expose per-service group_data_prot and device-global group_mgmt_prot.
ESP32-C2 and ESP32-C61 have no RSA based Secure Boot V2 support, so the
CI configs that pin the RSA signing scheme and key fail the app signing
scheme/key check on these targets.
- flash_enc_wifi_2.data_partition_verification: add C2/C61 sdkconfig
overlays that switch to the ECDSA P-256 signing scheme and key (no
force-enable needed as Secure Boot V2 itself is not enabled here).
- on_update_no_sb_rsa: disable the build on targets without
SOC_SECURE_BOOT_V2_RSA, mirroring simple_ota_example, since this
config specifically exercises the RSA scheme.
When the NimBLE stack called this callback for a GATT Write Request, the
uninitialized stack value was interpreted as a non-zero GATT error code,
causing the stack to send BLE_ATT_ERR_UNLIKELY (0x0E) back to the client.
fix(mmap): fixed mmap read data wrong when flash being erased/written and cache not disabled
Closes IDFGH-14084
See merge request espressif/esp-idf!29804
Address these:
lock_example.c:162:60: error: cast to pointer from integer of different size
[-Werror=int-to-pointer-cast]
162 | xTaskCreatePinnedToCore(inc_num_mutex, NULL, 4096, (void *)thread_id, TASK_PRIO_3, NULL, tskNO_AFFINITY);
| ^
create_task_example.c:30:19: error: cast from pointer to integer of different size
[-Werror=pointer-to-int-cast]
30 | int task_id = (int)arg;
Move the RGB panel initialization out of the shared example component
and into example-local files so the LCD setup flow and Kconfig stay
close to the example. Rename the helper APIs and sync the log
expectations so the teaching-oriented example remains easier to follow.
Add ESP_KEY_SOURCE_BUFFER and ESP_KEY_SOURCE_PSA key sources so all
hardware backends (DS, ECDSA, secure element) are accessed via PSA
key IDs through a single esp_tls_cfg_t.client_key field.
C.S.M
Rahul Tank
Wang Meng Yang
morris
Aditya Patwardhan
yangfeng
Marius Vikhammer
nilesh.kale
Sudeep Mohanty
Jiang Jiang Jian
Guillaume Souchere
Meet Patel
Harshal Patil
Sarvesh Bodakhe
Island
Hu Rui
cjin
Shuai Wang
Liu Linyan
Michael (XIAO Xufeng)
Richard Allen
Shu Chen
yuanhonghui
yiwenxiu