Reset the LP SPI peripheral and GPIOs before and after every SPI case so
each test starts from a known-clean baseline, and gate the master on an
explicit slave-armed handshake so the master cannot clock the bus while
the slave is still in its arm prologue. Verify received data against the
expected pattern with bounded waits instead of merely logging it.
Add a dedicated LP SPI multi-device pytest for esp32p4 that runs the
retagged lp_core_spi cases, and tag the LP I2C case accordingly.
The multi-device LP UART tests were failing on esp32p4 due to several
issues in the test harness:
- LP ROM boot banner: On chips with LP ROM (esp32p4), the LP core emits
a ROM banner on LP UART during startup, corrupting the first bytes of
test data. Set skip_lp_rom_boot=true in the ULP config for write, read
and mismatch tests to suppress this.
- Stale FIFO data: The HP UART RX FIFO could accumulate garbage during
pin mux setup. Add uart_flush_input() after HP UART driver installation
and before each read phase. Call lp_core_uart_clear_buf() before LP-side
read tests to flush the LP UART RX FIFO as well.
- Missing synchronization: The HP reader could start listening before
the LP transmitter was ready (or vice versa), causing data loss at
higher baud rates. Add signal exchange (unity_send_signal /
unity_wait_for_signal) to coordinate LP-to-HP data transfers.
- Short read timeout: The uart_read_bytes() timeout of 10 ms was too
aggressive for slower baud rates. Increase to 100 ms.
Made-with: Cursor
Several LP core pytest files were either hardcoded to specific chip lists
or using a less-precise SOC capability filter:
- test_lp_core_multi_device: was locked to ['esp32c6'] pending a workaround
for LP I2C on esp32p4; all three active LP core chips now have
SOC_LP_I2C_SUPPORTED=1, so switch to soc_filtered_targets.
- test_lp_uart_wakeup_modes: was using SOC_LP_CORE_SUPPORTED which is
semantically wrong for a UART test; change to SOC_ULP_LP_UART_SUPPORTED.
- LP core example pytests (build_system, interrupt, gpio_intr_pulse_counter,
lp_timer_interrupt): replace hardcoded ['esp32c5', 'esp32c6', 'esp32p4']
with soc_filtered_targets('SOC_LP_CORE_SUPPORTED == 1') so that new
chips automatically get coverage when their SOC cap is enabled.
Refactor the LP UART multi-device tests to use a single parameterised
helper pair (test_lp_uart_write_cfg / test_lp_uart_read_cfg) instead of
one-off functions per config, and extend coverage to:
- write and read tests for 5-, 6-, 7-bit and even-parity configurations
- negative tests: word-length mismatch (FRAM_ERR recovery on LP side,
garbled receive on HP side)
- LP GPIO Matrix routing tests (SOC_LP_GPIO_MATRIX_SUPPORTED chips only):
swaps the default TX/RX GPIO numbers so both pins go through the LP GPIO
Matrix, covering the lp_gpio_connect_in/out_signal() branch of
lp_uart_config_io() that was previously untested at the data-transfer
level; the same physical cross-wiring as all other LP UART tests is reused
Add rtc_gpio_deinit() cleanup at the end of single-board LP UART tests
so configured pins are returned to HP/digital mode and do not interfere
with subsequent tests that may reuse the same GPIOs.
Use dual-path macros: C keeps fragment-style designated initializers;
C++ uses GNU statement expressions (ESP_LOG_CONFIG_INIT pattern).
Add compile-only C++ regression tests for LP UART/I2C and ULP RISC-V I2C.
Closes https://github.com/espressif/esp-idf/issues/18369
Co-authored-by: Cursor <cursoragent@cursor.com>
The test was passing without real I2C communication due to a GPIO
mismatch (slave on GPIO 6/7 vs RTC I2C master on GPIO 2/3), single-byte
zero-coincidence, unchecked ULP return values, and an insufficient
RTC I2C timeout.
Fix slave GPIOs, increase test length, check I2C return values, add
proper assertions, and set an adequate RTC I2C timeout.
Co-authored-by: Cursor <cursoragent@cursor.com>
When ulp_lp_core_wakeup_main_processor() is called, it sets the
PMU_SW_INT_RAW bit on the HP side. The normal sleep path clears this
bit before re-entering sleep, but esp_wake_stub_sleep() did not, leaving
the wakeup cause sticky. This caused the PMU to immediately re-trigger a
wakeup as soon as sleep was requested from the wake stub, producing a
rapid re-wakeup loop that eventually triggered LP_WDT_SYS resets.
Add a test case that verifies the wake stub can return to sleep correctly
across multiple LP core wakeup cycles without the re-wakeup bug.
Closing https://github.com/espressif/esp-idf/issues/18308
Made-with: Cursor
lp_core_i2c.h header file has sda and scl pins hardcoded to GPIO6 and
GPIO7 which works only for ESP32C6. ESP32C5 uses GPIO2 and GPIO3 for
I2C SDA and SCL. Hence, added LP_I2C_SCL_IO and LP_I2C_SDA_IO macros
under conditional compilation in library header file, so there is no
need to hardcode I2C GPIO pins and any other test apps or examples
that are including the LP I2C header file can also use Macro directly.
This commit:
- Removes the link time symbol name clash detection.
- Extracts symbols of type NOTYPE for global identifiers defined in
assembly files.
- Makes the prefix argument optional for ulp_add_build_binary_targets().
- Adds a unit test for the ulp binary embed with a prefix feature.
Jiang Jiang Jian
Marius Vikhammer
Sudeep Mohanty
hebinglin
Konstantin Kondrashov
wanckl
armando
Meet Patel
igor.udot
Song Ruo Jing
gaoxu
Wu Zheng Hui