diff --git a/components/driver/twai/Kconfig.twai b/components/driver/twai/Kconfig.twai
index 11ff4187296..7ed12e03f17 100644
--- a/components/driver/twai/Kconfig.twai
+++ b/components/driver/twai/Kconfig.twai
@@ -7,12 +7,6 @@ menu "Legacy TWAI Driver Configurations"
         help
             Place the TWAI ISR in to IRAM to reduce latency and increase performance
 
-    config TWAI_SKIP_LEGACY_CONFLICT_CHECK
-        bool "Skip legacy driver conflict check"
-        default n
-        help
-            This configuration option used to bypass the conflict check mechanism with legacy code.
-
     config TWAI_SUPPRESS_DEPRECATE_WARN
         bool "Suppress legacy driver deprecated warning"
         default n
@@ -21,57 +15,10 @@ menu "Legacy TWAI Driver Configurations"
             (driver/twai.h). If you want to continue using the legacy driver,
             and don't want to see related deprecation warnings, you can enable this option.
 
-    config TWAI_ERRATA_FIX_BUS_OFF_REC
-        bool "Add SW workaround for REC change during bus-off"
-        depends on IDF_TARGET_ESP32
-        default y
+    config TWAI_SKIP_LEGACY_CONFLICT_CHECK
+        bool "Skip legacy driver conflict check"
+        default n
         help
-            When the bus-off condition is reached, the REC should be reset to 0 and frozen (via LOM) by the
-            driver's ISR. However on the ESP32, there is an edge case where the REC will increase before the
-            driver's ISR can respond in time (e.g., due to the rapid occurrence of bus errors), thus causing the
-            REC to be non-zero after bus-off. A non-zero REC can prevent bus-off recovery as the bus-off recovery
-            condition is that both TEC and REC become 0. Enabling this option will add a workaround in the driver
-            to forcibly reset REC to zero on reaching bus-off.
-
-    config TWAI_ERRATA_FIX_TX_INTR_LOST
-        bool "Add SW workaround for TX interrupt lost errata"
-        depends on IDF_TARGET_ESP32
-        default y
-        help
-            On the ESP32, when a transmit interrupt occurs, and interrupt register is read on the same APB clock
-            cycle, the transmit interrupt could be lost. Enabling this option will add a workaround that checks the
-            transmit buffer status bit to recover any lost transmit interrupt.
-
-    config TWAI_ERRATA_FIX_RX_FRAME_INVALID
-        bool "Add SW workaround for invalid RX frame errata"
-        depends on IDF_TARGET_ESP32
-        default y
-        help
-            On the ESP32, when receiving a data or remote frame, if a bus error occurs in the data or CRC field,
-            the data of the next received frame could be invalid. Enabling this option will add a workaround that
-            will reset the peripheral on detection of this errata condition. Note that if a frame is transmitted on
-            the bus whilst the reset is ongoing, the message will not be receive by the peripheral sent on the bus
-            during the reset, the message will be lost.
-
-    config TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
-        bool "Add SW workaround for RX FIFO corruption errata"
-        depends on IDF_TARGET_ESP32
-        default y
-        help
-            On the ESP32, when the RX FIFO overruns and the RX message counter maxes out at 64 messages, the entire
-            RX FIFO is no longer recoverable. Enabling this option will add a workaround that resets the peripheral
-            on detection of this errata condition. Note that if a frame is being sent on the bus during the reset
-            bus during the reset, the message will be lost.
-
-    config TWAI_ERRATA_FIX_LISTEN_ONLY_DOM
-        bool "Add SW workaround for listen only transmits dominant bit errata"
-        depends on IDF_TARGET_ESP32 || IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3 || IDF_TARGET_ESP32C3
-        default y
-        help
-            When in the listen only mode, the TWAI controller must not influence the TWAI bus (i.e., must not send
-            any dominant bits). However, while in listen only mode on the ESP32/ESP32-S2/ESP32-S3/ESP32-C3, the
-            TWAI controller will still transmit dominant bits when it detects an error (i.e., as part of an active
-            error frame). Enabling this option will add a workaround that forces the TWAI controller into an error
-            passive state on initialization, thus preventing any dominant bits from being sent.
+            This configuration option used to bypass the conflict check mechanism with legacy code.
 
 endmenu # TWAI Configuration
diff --git a/components/driver/twai/linker.lf b/components/driver/twai/linker.lf
index 2d0c47b0b95..968506ed339 100644
--- a/components/driver/twai/linker.lf
+++ b/components/driver/twai/linker.lf
@@ -23,7 +23,7 @@ entries:
         twai_hal_v1: twai_hal_check_state_flags (noflash)
         twai_hal_v1: twai_hal_clear_rx_fifo_overrun (noflash)
 
-        if TWAI_ERRATA_FIX_RX_FRAME_INVALID = y || TWAI_ERRATA_FIX_RX_FIFO_CORRUPT = y:
+        if IDF_TARGET_ESP32 = y:    #For errata workarounds
             twai_hal_v1: twai_hal_prepare_for_reset (noflash)
             twai_hal_v1: twai_hal_recover_from_reset (noflash)
             twai_hal_v1: twai_hal_backup_config (noflash)
diff --git a/components/driver/twai/twai.c b/components/driver/twai/twai.c
index 5a42e178171..3b107c7b718 100644
--- a/components/driver/twai/twai.c
+++ b/components/driver/twai/twai.c
@@ -226,8 +226,11 @@ static void twai_intr_handler_main(void *arg)
     portENTER_CRITICAL_ISR(&p_twai_obj->spinlock);
     events = twai_hal_get_events(p_twai_obj->hal);    //Get the events that triggered the interrupt
 
-#if defined(CONFIG_TWAI_ERRATA_FIX_RX_FRAME_INVALID) || defined(CONFIG_TWAI_ERRATA_FIX_RX_FIFO_CORRUPT)
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
+    // Errata workaround: Reset the peripheral on detection of this errata condition.
+    // Note that if a frame is being sent on the bus during the reset, the message will be lost.
     if (events & TWAI_HAL_EVENT_NEED_PERIPH_RESET) {
+        ESP_EARLY_LOGD(TWAI_TAG, "Triggered peripheral reset");
         twai_hal_prepare_for_reset(p_twai_obj->hal);
         TWAI_RCC_ATOMIC() {
             twai_ll_reset_register(p_twai_obj->controller_id);
diff --git a/components/esp_driver_twai/Kconfig b/components/esp_driver_twai/Kconfig
index e9ace179f15..1b979310563 100644
--- a/components/esp_driver_twai/Kconfig
+++ b/components/esp_driver_twai/Kconfig
@@ -18,7 +18,7 @@ menu "ESP-Driver:TWAI Configurations"
     config TWAI_ISR_CACHE_SAFE
         bool "Allow TWAI ISR execute when cache disabled" if !SPI_FLASH_AUTO_SUSPEND
         select TWAI_ISR_IN_IRAM
-        select ESP_PERIPH_CTRL_FUNC_IN_IRAM if TWAI_ERRATA_FIX_RX_FRAME_INVALID || TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
+        select ESP_PERIPH_CTRL_FUNC_IN_IRAM if IDF_TARGET_ESP32 #For errata workarounds
         default n
         help
             Allow TWAI works under Cache disabled (such as when writing to SPI Flash),
diff --git a/components/esp_driver_twai/esp_twai_onchip.c b/components/esp_driver_twai/esp_twai_onchip.c
index f83b76dc31f..7a8440842ed 100644
--- a/components/esp_driver_twai/esp_twai_onchip.c
+++ b/components/esp_driver_twai/esp_twai_onchip.c
@@ -201,8 +201,11 @@ static void _node_isr_main(void *arg)
     twai_onchip_ctx_t *twai_ctx = arg;
     uint32_t events = twai_hal_get_events(twai_ctx->hal);    //Get the events that triggered the interrupt
 
-#if CONFIG_IDF_TARGET_ESP32 // only esp32 have this errata, TODO: IDF-13002 check errata runtime
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
+    // Errata workaround: Reset the peripheral on detection of this errata condition.
+    // Note that if a frame is being sent on the bus during the reset, the message will be lost.
     if (events & TWAI_HAL_EVENT_NEED_PERIPH_RESET) {
+        ESP_EARLY_LOGD(TAG, "Triggered peripheral reset");
         twai_hal_prepare_for_reset(twai_ctx->hal);
         TWAI_RCC_ATOMIC() {
             twai_ll_reset_register(twai_ctx->ctrlr_id);
@@ -498,7 +501,7 @@ static esp_err_t _node_disable(twai_node_handle_t node)
     ESP_RETURN_ON_ERROR(esp_intr_disable(twai_ctx->intr_hdl), TAG, "disable interrupt failed");
     atomic_store(&twai_ctx->state, TWAI_ERROR_BUS_OFF);
     twai_hal_stop(twai_ctx->hal);
-#if CONFIG_IDF_TARGET_ESP32 // only esp32 have this errata, TODO: IDF-13002 check errata runtime
+#if TWAI_LL_HAS_RX_FRAME_ISSUE
     // when `disable` happens during hardware busy, the next RX frame is corrupted, a HW reset can fix it
     if (twai_hal_is_hw_busy(twai_ctx->hal)) {
         twai_hal_backup_config(twai_ctx->hal);
diff --git a/components/hal/esp32/include/hal/twai_ll.h b/components/hal/esp32/include/hal/twai_ll.h
index 59a0513d7e9..036a8e6c610 100644
--- a/components/hal/esp32/include/hal/twai_ll.h
+++ b/components/hal/esp32/include/hal/twai_ll.h
@@ -28,7 +28,30 @@
 #include "soc/dport_reg.h"
 
 #define TWAI_LL_GET_HW(controller_id) ((controller_id == 0) ? (&TWAI) : NULL)
-#define TWAI_LL_BRP_DIV_THRESH       128
+
+// When the bus-off condition is reached, the REC should be reset to 0 and frozen (via LOM) by the
+// driver's ISR. However on the ESP32, there is an edge case where the REC will increase before the
+// driver's ISR can respond in time (e.g., due to the rapid occurrence of bus errors), thus causing the
+// REC to be non-zero after bus-off. A non-zero REC can prevent bus-off recovery as the bus-off recovery
+// condition is that both TEC and REC become 0.
+#define TWAI_LL_HAS_BUSOFF_REC_ISSUE    1
+
+// On the ESP32, when a transmit interrupt occurs, and interrupt register is read on the same APB clock
+// cycle, the transmit interrupt could be lost.
+#define TWAI_LL_HAS_INTR_LOST_ISSUE     1
+
+// When in the listen only mode, the TWAI controller must not influence the TWAI bus (i.e., must not send
+// any dominant bits). However, while in listen only mode, the TWAI controller will still transmit dominant
+// bits when it detects an error (i.e., as part of an active error frame).
+#define TWAI_LL_HAS_LOM_DOM_ISSUE       1
+
+// On the ESP32, when the RX FIFO overruns and the RX message counter maxes out at 64 messages, the entire
+// RX FIFO is no longer recoverable.
+#define TWAI_LL_HAS_RX_FIFO_ISSUE       1
+
+// On the ESP32, when receiving a data or remote frame, if a bus error occurs in the data or CRC field,
+// the data field of the NEXT received frame could be invalid.
+#define TWAI_LL_HAS_RX_FRAME_ISSUE      1
 
 #ifdef __cplusplus
 extern "C" {
@@ -38,6 +61,7 @@ static uint32_t twai_ll_get_brp_max(void);
 /* ------------------------- Defines and Typedefs --------------------------- */
 #define TWAI_LL_BRP_MIN         2
 #define TWAI_LL_BRP_MAX         twai_ll_get_brp_max()   // max brp of esp32 is depends on chip version
+#define TWAI_LL_BRP_DIV_THRESH  128
 #define TWAI_LL_TSEG1_MIN       1
 #define TWAI_LL_TSEG2_MIN       1
 #define TWAI_LL_TSEG1_MAX       16  //the max register value
diff --git a/components/hal/esp32c3/include/hal/twai_ll.h b/components/hal/esp32c3/include/hal/twai_ll.h
index a1a7c3d0596..c1a19c68c2d 100644
--- a/components/hal/esp32c3/include/hal/twai_ll.h
+++ b/components/hal/esp32c3/include/hal/twai_ll.h
@@ -27,6 +27,11 @@
 
 #define TWAI_LL_GET_HW(controller_id) ((controller_id == 0) ? (&TWAI) : NULL)
 
+// When in the listen only mode, the TWAI controller must not influence the TWAI bus (i.e., must not send
+// any dominant bits). However, while in listen only mode, the TWAI controller will still transmit dominant
+// bits when it detects an error (i.e., as part of an active error frame).
+#define TWAI_LL_HAS_LOM_DOM_ISSUE       1
+
 #ifdef __cplusplus
 extern "C" {
 #endif
diff --git a/components/hal/esp32s2/include/hal/twai_ll.h b/components/hal/esp32s2/include/hal/twai_ll.h
index a46717c2c52..a224b9523f9 100644
--- a/components/hal/esp32s2/include/hal/twai_ll.h
+++ b/components/hal/esp32s2/include/hal/twai_ll.h
@@ -27,6 +27,11 @@
 
 #define TWAI_LL_GET_HW(controller_id) ((controller_id == 0) ? (&TWAI) : NULL)
 
+// When in the listen only mode, the TWAI controller must not influence the TWAI bus (i.e., must not send
+// any dominant bits). However, while in listen only mode, the TWAI controller will still transmit dominant
+// bits when it detects an error (i.e., as part of an active error frame).
+#define TWAI_LL_HAS_LOM_DOM_ISSUE       1
+
 #ifdef __cplusplus
 extern "C" {
 #endif
diff --git a/components/hal/esp32s3/include/hal/twai_ll.h b/components/hal/esp32s3/include/hal/twai_ll.h
index 965f162859e..538a40e1292 100644
--- a/components/hal/esp32s3/include/hal/twai_ll.h
+++ b/components/hal/esp32s3/include/hal/twai_ll.h
@@ -27,6 +27,11 @@
 
 #define TWAI_LL_GET_HW(controller_id) ((controller_id == 0) ? (&TWAI) : NULL)
 
+// When in the listen only mode, the TWAI controller must not influence the TWAI bus (i.e., must not send
+// any dominant bits). However, while in listen only mode, the TWAI controller will still transmit dominant
+// bits when it detects an error (i.e., as part of an active error frame).
+#define TWAI_LL_HAS_LOM_DOM_ISSUE       1
+
 #ifdef __cplusplus
 extern "C" {
 #endif
diff --git a/components/hal/include/hal/twai_types_deprecated.h b/components/hal/include/hal/twai_types_deprecated.h
index 3dfe57d5225..1752c786665 100644
--- a/components/hal/include/hal/twai_types_deprecated.h
+++ b/components/hal/include/hal/twai_types_deprecated.h
@@ -8,9 +8,9 @@
 
 #include <stdint.h>
 #include <stdbool.h>
-#include "sdkconfig.h"
 #include "soc/soc_caps.h"
 #include "soc/clk_tree_defs.h"
+#include "hal/config.h"
 
 #ifdef __cplusplus
 extern "C" {
@@ -56,11 +56,11 @@ extern "C" {
 #define TWAI_TIMING_CONFIG_10KBITS()    {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 200000, .brp = 0, .prop_seg = 0, .tseg_1 = 15, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #endif // SOC_TWAI_BRP_MAX > 256
 
-#if (SOC_TWAI_BRP_MAX > 128) || (CONFIG_ESP32_REV_MIN_FULL >= 200)
+#if (SOC_TWAI_BRP_MAX > 128) || (SOC_IS(ESP32) && (HAL_CONFIG(CHIP_SUPPORT_MIN_REV) >= 200))
 #define TWAI_TIMING_CONFIG_12_5KBITS()  {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 312500, .brp = 0, .prop_seg = 0, .tseg_1 = 16, .tseg_2 = 8, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #define TWAI_TIMING_CONFIG_16KBITS()    {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 400000, .brp = 0, .prop_seg = 0, .tseg_1 = 16, .tseg_2 = 8, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #define TWAI_TIMING_CONFIG_20KBITS()    {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 400000, .brp = 0, .prop_seg = 0, .tseg_1 = 15, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
-#endif // (SOC_TWAI_BRP_MAX > 128) || (CONFIG_ESP32_REV_MIN_FULL >= 200)
+#endif
 
 #if SOC_TWAI_CLK_SUPPORT_XTAL
 #define TWAI_TIMING_CONFIG_25KBITS()    {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 500000, .brp = 0, .prop_seg = 0, .tseg_1 = 15, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
@@ -71,7 +71,7 @@ extern "C" {
 #define TWAI_TIMING_CONFIG_100KBITS()   {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 2000000, .brp = 0, .prop_seg = 0, .tseg_1 = 15, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #define TWAI_TIMING_CONFIG_125KBITS()   {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 2000000, .brp = 0, .prop_seg = 0, .tseg_1 = 11, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #define TWAI_TIMING_CONFIG_250KBITS()   {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 4000000, .brp = 0, .prop_seg = 0, .tseg_1 = 11, .tseg_2 = 4, .sjw = 2, .ssp_offset = 0, .triple_sampling = false}
-#if SOC_TWAI_CLK_SUPPORT_XTAL && CONFIG_XTAL_FREQ == 40   // TWAI_CLK_SRC_XTAL = 40M
+#if SOC_TWAI_CLK_SUPPORT_XTAL && HAL_CONFIG(XTAL_HINT_FREQ_MHZ) == 40   // TWAI_CLK_SRC_XTAL = 40M
 #define TWAI_TIMING_CONFIG_500KBITS()   {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 10000000, .brp = 0, .prop_seg = 0, .tseg_1 = 15, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #define TWAI_TIMING_CONFIG_800KBITS()   {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 20000000, .brp = 0, .prop_seg = 0, .tseg_1 = 16, .tseg_2 = 8, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
 #define TWAI_TIMING_CONFIG_1MBITS()     {.clk_src = TWAI_CLK_SRC_DEFAULT, .quanta_resolution_hz = 20000000, .brp = 0, .prop_seg = 0, .tseg_1 = 15, .tseg_2 = 4, .sjw = 3, .ssp_offset = 0, .triple_sampling = false}
diff --git a/components/hal/twai_hal_v1.c b/components/hal/twai_hal_v1.c
index e063bdffa93..a3590816eb9 100644
--- a/components/hal/twai_hal_v1.c
+++ b/components/hal/twai_hal_v1.c
@@ -5,8 +5,8 @@
  */
 
 #include <stddef.h>
-#include "sdkconfig.h"
 #include "esp_compiler.h"
+#include "hal/log.h"
 #include "hal/twai_hal.h"
 #include "hal/twai_ll.h"
 #include "soc/soc_caps.h"
@@ -16,7 +16,8 @@
 #define TWAI_HAL_INIT_REC    0
 #define TWAI_HAL_INIT_EWL    96
 
-#if CONFIG_IDF_TARGET_ESP32 // only esp32 have this errata, TODO: IDF-13002 check errata runtime
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
+// context for errata workarounds
 typedef struct twai_hal_errata_ctx_t {
     twai_hal_frame_t tx_frame_save;
     twai_ll_reg_save_t reg_save;
@@ -25,7 +26,7 @@ typedef struct twai_hal_errata_ctx_t {
 #endif
 
 size_t twai_hal_get_mem_requirment(void) {
-#if CONFIG_IDF_TARGET_ESP32 // only esp32 have this errata, TODO: IDF-13002 check errata runtime
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
     return sizeof(twai_hal_context_t) + sizeof(twai_hal_errata_ctx_t);
 #else
     return sizeof(twai_hal_context_t);
@@ -48,7 +49,7 @@ bool twai_hal_init(twai_hal_context_t *hal_ctx, const twai_hal_config_t *config)
     if (!twai_ll_is_in_reset_mode(hal_ctx->dev)) {    //Must enter reset mode to write to config registers
         return false;
     }
-#if CONFIG_IDF_TARGET_ESP32 // only esp32 have this errata, TODO: IDF-13002 check errata runtime
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
     hal_ctx->errata_ctx = (twai_hal_errata_ctx_t *)(hal_ctx + 1);   //errata context is place at end of hal_ctx
 #endif
 #if SOC_TWAI_SUPPORT_MULTI_ADDRESS_LAYOUT
@@ -143,12 +144,10 @@ void twai_hal_start(twai_hal_context_t *hal_ctx)
     twai_ll_set_mode(hal_ctx->dev, hal_ctx->enable_listen_only, hal_ctx->enable_self_test, hal_ctx->enable_loopback);
     //Clear the TEC and REC
     twai_ll_set_tec(hal_ctx->dev, 0);
-#ifdef CONFIG_TWAI_ERRATA_FIX_LISTEN_ONLY_DOM
-    /*
-    Errata workaround: Prevent transmission of dominant error frame while in listen only mode by setting REC to 128
-    before exiting reset mode. This forces the controller to be error passive (thus only transmits recessive bits).
-    The TEC/REC remain frozen in listen only mode thus ensuring we remain error passive.
-    */
+#if TWAI_LL_HAS_LOM_DOM_ISSUE
+    // Errata workaround: Prevent transmission of dominant error frame while in listen only mode by setting REC to 128
+    // before exiting reset mode. This forces the controller to be error passive (thus only transmits recessive bits).
+    // The TEC/REC remain frozen in listen only mode thus ensuring we remain error passive.
     if (hal_ctx->enable_listen_only) {
         twai_ll_set_rec(hal_ctx->dev, 128);
     } else
@@ -179,7 +178,7 @@ void twai_hal_start_bus_recovery(twai_hal_context_t *hal_ctx)
 
 /* ------------------------------------ IRAM Content ------------------------------------ */
 
-#ifdef CONFIG_TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
+#if TWAI_LL_HAS_RX_FIFO_ISSUE
 //Errata condition occurs at 64 messages. Threshold set to 62 to prevent the chance of failing to detect errata condition.
 #define TWAI_RX_FIFO_CORRUPT_THRESH     62
 #endif
@@ -231,7 +230,8 @@ static inline uint32_t twai_hal_decode_interrupt(twai_hal_context_t *hal_ctx)
         TWAI_HAL_SET_BITS(events, TWAI_HAL_EVENT_RX_BUFF_FRAME);
     }
     //Transmit interrupt set whenever TX buffer becomes free
-#ifdef CONFIG_TWAI_ERRATA_FIX_TX_INTR_LOST
+#if TWAI_LL_HAS_INTR_LOST_ISSUE
+    // Errata workaround: Check the transmit buffer status bit to recover any lost transmit interrupt.
     if ((interrupts & TWAI_LL_INTR_TI || hal_ctx->state_flags & TWAI_HAL_STATE_FLAG_TX_BUFF_OCCUPIED) && status & TWAI_LL_STATUS_TBS) {
 #else
     if (interrupts & TWAI_LL_INTR_TI) {
@@ -270,7 +270,7 @@ uint32_t twai_hal_get_events(twai_hal_context_t *hal_ctx)
 
     //Handle low latency events
     if (events & TWAI_HAL_EVENT_BUS_OFF) {
-#ifdef CONFIG_TWAI_ERRATA_FIX_BUS_OFF_REC
+#if TWAI_LL_HAS_BUSOFF_REC_ISSUE
         //Errata workaround: Force REC to 0 by re-triggering bus-off (by setting TEC to 0 then 255)
         twai_ll_set_tec(hal_ctx->dev, 0);
         twai_ll_set_tec(hal_ctx->dev, 255);
@@ -289,25 +289,27 @@ uint32_t twai_hal_get_events(twai_hal_context_t *hal_ctx)
             .ack_err = (type == TWAI_LL_ERR_OTHER) && (seg == TWAI_LL_ERR_SEG_ACK_SLOT),
         };
         hal_ctx->errors = errors;
-#ifdef CONFIG_TWAI_ERRATA_FIX_RX_FRAME_INVALID
+#if TWAI_LL_HAS_RX_FRAME_ISSUE
         //Check for errata condition (RX message has bus error at particular segments)
         if (dir == TWAI_LL_ERR_DIR_RX &&
             ((seg == TWAI_LL_ERR_SEG_DATA || seg == TWAI_LL_ERR_SEG_CRC_SEQ) ||
              (seg == TWAI_LL_ERR_SEG_ACK_DELIM && type == TWAI_LL_ERR_OTHER))) {
             TWAI_HAL_SET_BITS(events, TWAI_HAL_EVENT_NEED_PERIPH_RESET);
+            HAL_LOGD("TWAI_HAL", "RX frame invalid detected");
         }
 #endif
     }
     if (events & TWAI_HAL_EVENT_ARB_LOST) {
         twai_ll_clear_arb_lost_cap(hal_ctx->dev);
     }
-#ifdef CONFIG_TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
+#if TWAI_LL_HAS_RX_FIFO_ISSUE
     //Check for errata condition (rx_msg_count >= corruption_threshold)
     if (events & TWAI_HAL_EVENT_RX_BUFF_FRAME && twai_ll_get_rx_msg_count(hal_ctx->dev) >= TWAI_RX_FIFO_CORRUPT_THRESH) {
         TWAI_HAL_SET_BITS(events, TWAI_HAL_EVENT_NEED_PERIPH_RESET);
+        HAL_LOGD("TWAI_HAL", "RX FIFO corruption detected");
     }
 #endif
-#if defined(CONFIG_TWAI_ERRATA_FIX_RX_FRAME_INVALID) || defined(CONFIG_TWAI_ERRATA_FIX_RX_FIFO_CORRUPT)
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
     if (events & TWAI_HAL_EVENT_NEED_PERIPH_RESET) {
         //A peripheral reset will invalidate an RX event;
         TWAI_HAL_CLEAR_BITS(events, (TWAI_HAL_EVENT_RX_BUFF_FRAME));
@@ -316,7 +318,7 @@ uint32_t twai_hal_get_events(twai_hal_context_t *hal_ctx)
     return events;
 }
 
-#if CONFIG_IDF_TARGET_ESP32 // only esp32 have this errata, TODO: IDF-13002 check errata runtime
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
 bool twai_hal_is_hw_busy(twai_hal_context_t *hal_ctx)
 {
     return (TWAI_LL_STATUS_TS | TWAI_LL_STATUS_RS) & twai_ll_get_status(hal_ctx->dev);
@@ -365,7 +367,7 @@ void twai_hal_recover_from_reset(twai_hal_context_t *hal_ctx)
         TWAI_HAL_CLEAR_BITS(hal_ctx->state_flags, TWAI_HAL_STATE_FLAG_TX_NEED_RETRY);
     }
 }
-#endif // CONFIG_IDF_TARGET_ESP32
+#endif // TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
 
 void twai_hal_format_frame(const twai_hal_trans_desc_t *trans_desc, twai_hal_frame_t *frame)
 {
@@ -405,7 +407,7 @@ void twai_hal_set_tx_buffer_and_transmit(twai_hal_context_t *hal_ctx, twai_hal_f
         twai_ll_set_cmd_tx(hal_ctx->dev);
     }
     TWAI_HAL_SET_BITS(hal_ctx->state_flags, TWAI_HAL_STATE_FLAG_TX_BUFF_OCCUPIED);
-#if defined(CONFIG_TWAI_ERRATA_FIX_RX_FRAME_INVALID) || defined(CONFIG_TWAI_ERRATA_FIX_RX_FIFO_CORRUPT)
+#if TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
     if (&hal_ctx->errata_ctx->tx_frame_save == tx_frame) {
         return;
     }
@@ -413,7 +415,7 @@ void twai_hal_set_tx_buffer_and_transmit(twai_hal_context_t *hal_ctx, twai_hal_f
     ESP_COMPILER_DIAGNOSTIC_PUSH_IGNORE("-Wanalyzer-overlapping-buffers") // TODO IDF-11085
     memcpy(&hal_ctx->errata_ctx->tx_frame_save, tx_frame, sizeof(twai_hal_frame_t));
     ESP_COMPILER_DIAGNOSTIC_POP("-Wanalyzer-overlapping-buffers")
-#endif  //defined(CONFIG_TWAI_ERRATA_FIX_RX_FRAME_INVALID) || defined(CONFIG_TWAI_ERRATA_FIX_RX_FIFO_CORRUPT)
+#endif  //TWAI_LL_HAS_RX_FRAME_ISSUE || TWAI_LL_HAS_RX_FIFO_ISSUE
 }
 
 uint32_t twai_hal_get_rx_msg_count(twai_hal_context_t *hal_ctx)
diff --git a/tools/ci/sg_rules/no_kconfig_in_hal_component.yml b/tools/ci/sg_rules/no_kconfig_in_hal_component.yml
index b505efbf435..87ed8167825 100644
--- a/tools/ci/sg_rules/no_kconfig_in_hal_component.yml
+++ b/tools/ci/sg_rules/no_kconfig_in_hal_component.yml
@@ -12,10 +12,6 @@ ignores:
   - "components/hal/platform_port/**/*"
   - "components/hal/test_apps/**/*"
   - "components/esp_hal*/test_apps/**/*"
-  # the following files should be refactored to remove Kconfig macros
-  - "components/hal/twai_hal_v1.c"
-  - "components/hal/esp32/include/hal/twai_ll.h"
-  - "components/hal/include/hal/twai_types_deprecated.h"
 rule:
   any:
     - kind: argument_list
@@ -47,9 +43,6 @@ ignores:
   - "components/hal/platform_port/**/*"
   - "components/hal/test_apps/**/*"
   - "components/esp_hal*/test_apps/**/*"
-  # the following files should be refactored to remove sdkconfig.h
-  - "components/hal/twai_hal_v1.c"
-  - "components/hal/include/hal/twai_types_deprecated.h"
 rule:
   kind: preproc_include
   has: