feat(usb_device_example): Create per-target sdkconfig.defaults

examples/peripherals/usb/device/tusb_msc/README.md

@@ -59,7 +59,8 @@ GPIOs and SD bus settings can be configured in two ways:
    - Select "SDMMC CARD" for "Storage Media Used"
    - Select "SD/MMC bus width" — "4 lines (D0 - D3)" or "1 line (D0)" (see `CONFIG_EXAMPLE_SDMMC_BUS_WIDTH_1`)
    - On ESP32-S3 and ESP32-P4: set the GPIO numbers for the SD card interface
-2. In the source code: See the initialization of ``sdmmc_slot_config_t slot_config`` structure in the example code.
+2. Using target-specific defaults: Pin and LDO defaults for each chip are in ``sdkconfig.defaults.esp32s3``, ``sdkconfig.defaults.esp32p4``, and ``sdkconfig.defaults.esp32s31``. These are applied automatically when you set the target with ``idf.py set-target``.
+3. In the source code: See the initialization of ``sdmmc_slot_config_t slot_config`` structure in the example code.
 
 By default, this example uses 4-line SD mode, utilizing 6 pins: CLK, CMD, D0 - D3.
 

examples/peripherals/usb/device/tusb_msc/main/Kconfig.projbuild

@@ -13,7 +13,7 @@ menu "TinyUSB MSC Example Configuration"
 
         config EXAMPLE_STORAGE_MEDIA_SDMMC
             bool "SDMMC CARD"
-            depends on IDF_TARGET_ESP32S3 || IDF_TARGET_ESP32P4 || IDF_TARGET_ESP32S31
+            depends on SOC_SDMMC_HOST_SUPPORTED
     endchoice
 
     if EXAMPLE_STORAGE_MEDIA_SDMMC
@@ -39,40 +39,34 @@ menu "TinyUSB MSC Example Configuration"
             config EXAMPLE_PIN_CMD
                 int "CMD GPIO number"
                 range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
-                default 35 if IDF_TARGET_ESP32S3
+                default 35
-                default 44 if IDF_TARGET_ESP32P4
 
             config EXAMPLE_PIN_CLK
                 int "CLK GPIO number"
                 range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
-                default 36 if IDF_TARGET_ESP32S3
+                default 36
-                default 43 if IDF_TARGET_ESP32P4
 
             config EXAMPLE_PIN_D0
                 int "D0 GPIO number"
                 range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
-                default 37 if IDF_TARGET_ESP32S3
+                default 37
-                default 39 if IDF_TARGET_ESP32P4
 
             if EXAMPLE_SDMMC_BUS_WIDTH_4
 
                 config EXAMPLE_PIN_D1
                     int "D1 GPIO number"
                     range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
-                    default 38 if IDF_TARGET_ESP32S3
+                    default 38
-                    default 40 if IDF_TARGET_ESP32P4
 
                 config EXAMPLE_PIN_D2
                     int "D2 GPIO number"
                     range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
-                    default 33 if IDF_TARGET_ESP32S3
+                    default 33
-                    default 41 if IDF_TARGET_ESP32P4
 
                 config EXAMPLE_PIN_D3
                     int "D3 GPIO number"
                     range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
-                    default 34 if IDF_TARGET_ESP32S3
+                    default 34
-                    default 42 if IDF_TARGET_ESP32P4
 
             endif  # EXAMPLE_SDMMC_BUS_WIDTH_4
 
@@ -81,7 +75,6 @@ menu "TinyUSB MSC Example Configuration"
         config EXAMPLE_SD_PWR_CTRL_LDO_INTERNAL_IO
             depends on SOC_SDMMC_IO_POWER_EXTERNAL || SOC_SDMMC_IO_UHS_POWER_EXTERNAL
             bool "SDMMC powered by internal LDO"
-            default y
             help
                 Enable when internal LDO of an ESP32 is used as a power supply for SD card. Specify the LDO IO.
                 Disable when external power supply is used as a power supply for SD card.
@@ -90,8 +83,7 @@ menu "TinyUSB MSC Example Configuration"
             depends on SOC_SDMMC_IO_POWER_EXTERNAL || SOC_SDMMC_IO_UHS_POWER_EXTERNAL
             depends on EXAMPLE_SD_PWR_CTRL_LDO_INTERNAL_IO
             int "LDO IO"
-            default 4 if IDF_TARGET_ESP32P4
+            default 1
-            default 1 if IDF_TARGET_ESP32S31
             help
                 There are several IOs in ESP32 SD card capable targets which are in "SD card IO" power domain.
                 Power has to be supplied to this power domain externally (from outside the chip) via one of the pins.

examples/peripherals/usb/device/tusb_msc/sdkconfig.defaults.esp32p4

@@ -0,0 +1,8 @@
+CONFIG_EXAMPLE_PIN_CMD=44
+CONFIG_EXAMPLE_PIN_CLK=43
+CONFIG_EXAMPLE_PIN_D0=39
+CONFIG_EXAMPLE_PIN_D1=40
+CONFIG_EXAMPLE_PIN_D2=41
+CONFIG_EXAMPLE_PIN_D3=42
+CONFIG_EXAMPLE_SD_PWR_CTRL_LDO_INTERNAL_IO=y
+CONFIG_EXAMPLE_SD_PWR_CTRL_LDO_IO_ID=4

examples/peripherals/usb/device/tusb_msc/sdkconfig.defaults.esp32s3

@@ -0,0 +1,6 @@
+CONFIG_EXAMPLE_PIN_CMD=35
+CONFIG_EXAMPLE_PIN_CLK=36
+CONFIG_EXAMPLE_PIN_D0=37
+CONFIG_EXAMPLE_PIN_D1=38
+CONFIG_EXAMPLE_PIN_D2=33
+CONFIG_EXAMPLE_PIN_D3=34

examples/peripherals/usb/device/tusb_msc/sdkconfig.defaults.esp32s31

@@ -0,0 +1,2 @@
+CONFIG_EXAMPLE_SD_PWR_CTRL_LDO_INTERNAL_IO=y
+CONFIG_EXAMPLE_SD_PWR_CTRL_LDO_IO_ID=1